All About Dahlias

Apr 28, 2015

All About Dahlias

Apr 28, 2015

 

file1891294723876

During one August vacation my husband and youngest son happened upon the Swan Island Dahlia farm in Canby, Oregon (dahlias.com). “WOW!!” I was hooked.

I have now been growing dahlias for many years. There have been more successes some years that others, and I share my experiences below. Dahlias can be temperamental, so be patient until you find what works for you.

Location:  Dahlias like warm sun, not hot shade and they don't tolerate frost. They are best located in a situation that gets morning sun, but is protected some from the hot afternoon rays. Since they bloom late in the summer, the sooner you can get them started the better. They will wait for the soil to warm up before starting growth which can be hastened by planting in raised beds that warm quickly.

Preparation:  Dahlias like acid soil so I add 1 cup of sulfur per 100 square feet when preparing the ground. My dahlias performed best on the southwest side of the house in raised beds with good drainage.

Planting:  The tender tubers need to be planted well down in a 10-12 inch deep hole. Incorporate 2 tablespoons of bone meal into the bottom of the hole. Place the tuber on its side and drive in a sturdy stake next to it. By placing the stake now it serves as a marker, and also avoids the risk of damaging the roots or growing shoots which can happen once the hole is filled. I used 5ft 1inch redwood stake for my larger varieties. Cover the tuber initially with 4” of soil. Watch for sprouting and gradually fill in the hole as the plant grows.

Timing:  Because you plant your tuber underground, and you build soil around the new growth as it comes up, you can start your dahlias early. Spring planting is always a gamble in the high Desert. We have recorded frosts as late as June 8th. Getting a head start in the spring gives you more rewards from your plants. Be prepared to protect your dahlias from a sudden frost - Walls of water, frost cloths, etc.

I started my tubers on April 5, 2014 and had my fist flower on June 1st. Choose an early blooming variety if possible. I have had late varieties that never bloomed before the first frost in the fall! If your plant does get hit with a frost, it won't kill it, but it will have to start over.

You can also start your tubers indoors. When I tried this last year, I had more success with the tubers started outdoors. Although I can see where this might be a good option during a big winter and cold spring (If we ever get one of those again.)

Water:  Dahlias love water but usually the tubers don't need water until they sprout. In our climate (high desert) a light watering is often necessary until the plants emerge. When established you will want to give your plants a through deep watering about three times a week. I recommend a system that can deliver water to each individual plant so you don't waste the precious resource. Hand watering is not recommended because you won't get the necessary deep soaking needed. I have mine on a drip system which runs three times a week with a 1GPH emitter for 20 minutes. I supplemented that with a hose bubbler and flooded the beds every other week.

Fertilizer:  Use a fertilizer with a lot of Phosphorus for the blooms (this is the middle number of an NPK fertilizer.) A good choice is the same one you would use for your tomato plants. Follow the package directions. Fertilize after the first 3 weeks and then once a month until September. Stop fertilizing in September to promote a healthier tuber for winterizing.

Pests:  Slugs and snails love dahlias, especially little tender baby ones. Once you've filled in your planting hole, apply snail control around the top of your hole before the plant emerges to discourage them. Continue to apply throughout the season if the snails persist.

Later in the season as things warm up, watch for mites. If the lower leaves of your plant dry out and look like they need water, but you've been watering, you may have mites. Rinse the lower part of your plant to discourage mites. If you catch it early you may be able to wash them off, and remove the affected leaves. Mites won't kill the plant right away and you'll still get flowers on top. Normal fall frost is the first of October, so take all that into account before you resort to chemicals. Pesticides kill. Nature needs all of its checks and balances. For integrated pest management see http://www.ipm.ucdavis.edu/PMG/GARDEN/FLOWERS/dahlia.html .

Pruning:  This is the hardest part. As the stem emerges from the ground, the main stalk develops two branches on either side. After three of these branching pairs form on the stalk you have to pinch out the center. This encourages lower branching of the plant and will give you a stronger plant and more blooms on top!

Staking:  Staking is a must. Dahlias have hollow stems which often have to support very large (totally awesome) flowers that fall over easily, especially in our windy conditions.

Using the stake you placed at planting, every once in a while check and wrap a piece of garden twine around the entire plant with the stake in the middle, it will hold the plant up (unless you guessed wrong and your plant got too big, just add a second taller stake on the other side.) You don't need to tie up each individual stalk.

Harvest:  Sometimes this is a hard part - you might think that if you cut the flowers the plants will finish sooner, but the more you cut the more you get. One Fall I had several blooms on a couple of plants and thought we might get a frost so I cut them all off thinking that they were going to die anyway. Turns out we had a late frost that year and I was loaded with blooms after that! So now I feel guilty if I let a bloom expire on a plant without anyone enjoying it.

Cut your flowers in the cool of the morning, or evening before they are at the end of the bloom cycle. Not all dahlias are suitable for cutting, but I choose varieties that have long stems so I don't have to cut off the immature blooms in the same bunch. Have a pail of water handy to put them in as you harvest.

In the late summer, if your plants have a lot of buds, but don't seem to be blooming, they need more water.

Set the Bloom:  Some growers feel setting the bloom extends the life of the cut flowers. One way to set the blooms is to get several small containers of plastic, or metal (not glass, it holds heat.) Put 2-4 inches of hot (160-180 degrees F) in the bottom of the container. I use an electric hot water pot. I've also used the microwave, but don't use the container you use in the microwave to put your blooms in; it will be too hot since it is usually glass. Put the blooms in the cool containers with the couple inches of hot water with plenty of room for the steam to escape without affecting your flowers. Let the water cool for an hour or so, then transfer them to your vase.

Floral preservative will further extend the life of your cut flowers, although I just give my arrangements fresh water every day. The internet has many homemade preservative recipes, or you can buy commercial preservative.

A simple homemade preservative:

  • 1gallon water
  • 2 Tablespoons Sugar
  • 2 Tablespoons Vinegar
  • 1/2 Teaspoon Bleach

This is a good recipe to have, although I just give my arrangements fresh water every day. I'd like to do an experiment testing preservative vs daily fresh water or a combination to see what works best. But keeping it simple works best for me.

A subsequent article will cover lifting and storing the tubers at the end of the season.